AvTek's LLC Home Page...
AvTek New Address: 13487 Foresman Blvd
Port Charlotte; FL 33981 Tel 941/249-3736
AvTek New Address: 13487 Foresman Blvd Port Charlotte, Fl. 33981 WWW.avtek2.com
Buy NOW Here Orders for AircraftQuality Products Since 1983... Mike...30 years Contact us Recommend returning to the home page if you get lost in this web
It's Purchase...Save $$ Previously Owned Pulsar MOSFET, Call 941/249-3736 Single Light $225, Dual $395 BACK: $15.00 GE Halogen Landing (SOLD-OUT) Light w/Pulsar MOSFET Purchase.
Best Deal Seal Kit Only $10 More $134.95
Are your Panel Instruments ERRATIC and intermittent? ENGINE SLOW STARTS? NEW Price $125 ends soon
BOEING & Air-Bus Engineering all Commercial Aircraft using Bonding Technology
Bonding customer said: "flew yesterday , radio noises gone, steady gas gauges, starter turned well. Instructions were good. Mike is onto something here. Thanks Mike....Thanks FredShort Pirep on AvTek Bonding and Grounding Kit
Posted by Todt@KCCR (1677) on July 7, 2009, 5:36 pm
Thanks Todt...It's NOT "Rocket-Science"; just Simple Physics: Make all the Grounds BONDED to 0.010Ω which is like "Marriage" then seal-it... Kit has it all and....Just $125 SAY....Good-BYE to all your Electrical problems ONCE & for-ALL
Watch Pulsing 3-Landing Lights http://www.youtube.com/watch?v=fKg8sdj5L_E
Brighter > Using Power MOSFET's Click Here
Get the BEST; GET 2010 Technology Just $70 more it's Flawless...MOSFET comes with a LIFE-TIME warranty, it's that good.
YOU NEED a BETTER DOOR-SEAL; YES? Best Door-Seal-Kit
The "Air-Squeeze" Kit $149.95 contains -01/-02; (31 feet total) This Door-Seal has Air-Chambers
From: B. Dalton [mailto:email@example.com]
Michael, (Click Here for More)
This is in response to your request for comment concerning your door seals. I installed your seals in my 1988 Mooney 201. In short, the wind noise is gone! My aircraft mechanics had little trouble installing the seals and did review the information you have on your website and instructions that came with the seals. When I suggested that they install the seals without removing the door, their response was that was the only way to get good results. Cleaning all the old adhesive from the door is a must. My only concern is that the seals do stick to the door frame when the door is not opened for several weeks, especially in hot weather. I used to put a silicon dressing on my old seals (your competitor seal) to prevent this. I now longer have that problem.
I’m not sure when I saw your advertisement for the seals but think it might have been in the MAPA Log. I have since noticed it in several other publications. I have no suggestions as to the value of advertisement. I think most owners will go to the web to get some answers. Otherwise, I suggest you find some way to get to all A&E folks out there. They see every aircraft at least once a year and their suggestions concerning seal replacement would probably have more weight than all the copy I all the magazines.
Congratulations on an excellent (so far) product. It performs as advertised.
B. A. Dalton, MD
Click here for less confusion Door-Seal → Customer comments...some are Critical, we listen and changed
LOOK >> 1st Alert Now Plugs into Your Cig Lighter, NO install � IFR Pilots �
NOW…No Installation Cost Plugs Into Cig-Lighter. Smart Circuit Reads Amps/Volts on Buss…
Blinks Red Led when 12 minutes of Power is left in Ships Battery…All Aircraft & Boats
Buy the -02 Twin-Air Chamber Seal Kit Only $99.95 Works on 100% every Aircraft, soon FAA-PMA on Pressurized Models
Better Panel Lighting Click Picture: TekLitez
Please Call us at 1800/770-3265...
However, just like other internet companies we are pleased when you can place your order online...
........ but we also know sometimes you just need to talk...and I promise you this:
Your call will NEVER be answered by someone on the other side of the Planet. We Speak ONLY Aviation here.
13487 Foresman Blvd Port Charlotte, FL. 33981
Phone: [cell] 1800/770-3265 Please call this # 1st...it's a land-line 941/249-3736 [Florida]
This Many Visitors and Customers of AvTek LLC, USA 30 years, in 2013